dunder2k

hei jeg har en kangoo 1,4 2001 mod. jeg vil sette i større dynamo. er det bare til og skifte til større dynamo eller er det andre problemer? kunne tenkt meg en på 100A+ tenker ikke på fester og reimhjul. men rent eletrisk.. skal bare bruke den øverste i bilen, skal kjøpe 2stk. men hva kondensator bør jeg bruke? nye baterier, men hvilken kondonsator bør jeg bruke?

hei, nei nå røyk hele forsterkeren, jekk i fyr og flammer har du et alternativ til forsterker?

kjempe:D

brokoblet da?(siden det står minimum 2Ω).. takker for svar.

2 ohm

jeg har 3 VMAX 10" http://www.cerwinvega.com/VMAX10 forsterkeren er en soundmagus X3200 http://www.soundmagus.com/X3200.html så jeg lurte på om det var noen av dere som har noen forslag til kobling? tenkte 2 element i paralell (med seriekoblete spoler) å 1 i serie (med paralell spoler).

hei jeg snublet over en forsterker å lurte på om det var noen som har erfaring med de denne? TL-1021 Class D Specifications: Output Power (14.4v) (When bridging the channels) 1 x 8,000 watts Max (@ 2 ohm) 1 x 3,000 watts RMS (@ 2 ohm THD+N < 3.5%) 1 x 2,000 watts RMS (@ 4 ohm THD+N < 2%) Up to 1 x 3,400 watts RMS (@ 2 ohm) Up to 1 x 2,500w watts RMS (@ 4 ohm) Output Power (14.4v) (When using both channels individually) 2 x 4,000 watts Max (@ 1 ohm per channel) 2 x 1,500 watts RMS (@ 1 ohm per channel THD+N < 3%) 2 x 950 watts RMS (@ 2 ohm per channel THD+N < 2%) 2 x 600 watts RMS (@ 4 ohm per channel THD+N < 3%) 2 x 560 watts RMS (@ 4 ohm per channel THD+N < 1%) Frequency response 10 Hz ~ 200 Hz Subsonic Filter Frequency Range 20 ~ 50 Hz (Adjustable) Low Pass Filter Frequency Range 40 ~ 180 Hz (Adjustable) Bass Boost Frequency Range 45 Hz Input Impedance 67 Kohm Input sensitivity 0.2 V ~ 5 V Signal/Noise Ratio (A. Wtg) 1 Watt Reff. >100 dB Damping Factor (100 Hz @ 4 ohm) >120 Efficiency 82% Total Harmonic Distortion (THD) 4 ohm loaded 1 Watt 0.20% 800w RMS 0.50% 80% of total 0.70% Idle Current 2.4 A Max Peak Current 240 A Minimum Subwoofer impedance Each channel individually 1 ohm Minimum Subwoofer impedance when in bridge mode 2 ohm Power supply DC 12V Dimensions (length x width x height) dette sier ikke meg så veldig mye så jeg lurte på om dette er bra greier eller bare boss.. i tilleg så jeg denne subben TL-1121 Specifications: Parameter Data Unit Info Nom. diameter 12 [inch] Nominal diameter (30 cm) Vas 54.957 [Litres] Equivalent volume Qts 0.807 Total Speaker Q-factor Qes 0.905 Electrical Q-factor Qms 7.339 Mechanical Q-factor Fs 21.935 [Hz] Resonance Frequency (Free Air) Sensitivity 90.659 [dB] SPL dB at 1W, 1m Max Power 3000 [W] Maximum input power RMS Power 1000 [W] RMS input power xmax 20.32 [mm] Max excursion from centre at normal operation (one way) Moving mass 278.9 [g] (Mms) Weight of moving parts Disp area 0.0434 [m2] (SD), Effective piston area of cone Disp Vol 1763.8 [cm3] Displaced volume = xmax x 2 x SD Coil diameter 76.4 [mm] Diameter of the voice coil (Kapton 4-layer - 3") Cms 0.1888 [mm/N] The stiffness of the driver’s suspension Magnet weight 5102.9 [gr] Weight of the magnet (180 oz) Re 1.785 [ohm] DC resistance (per voice coil) Z 2 [ohm] Impedance of coil (per voice coil) L 2.23 [mH] Inductance of coil (per coil @ 1 kHz) Bl 27.529 [Tm] Magnetic strength (Motor force factor) Recommended sealed enclosure 0.0623 [m3] (2.2 cubic feet) Minimum sealed enclosure 0.034 [m3] (1.2 cubic feet) Recommended ported enclosure 0.0623 [m3] (2.2 cubic feet) Minimum ported enclosure 0.0425 [m3] (1.5 cubic feet) Krm 2 [m] Kxm 2.58 [mH] Rem 5.31 Erm 0.984 Exm 0.656 P max 3,000 Watts Maximum peak input power P rms 1,000 Watts Maximum RMS input power Magnet material High density strontium-ferrite takker for alle svar..